Leave Your Message
Porsche 718 Cayman GT4 Clubsport MR photographed on a race circuit
718 Cayman GT4 Clubsport MR. Photograph: Porsche AG.

Industry applications / Automotive & Racing

Automotive
& Racing

Machining composite parts
for road and track.

From a trimmed body panel to a battery-cover mounting hole, match the tool and inspection to the feature.

Explore machining tasks

Materials behind
the finished part.

A passenger cell, a racing panel and a battery case place different demands on finishing. These published examples show the construction behind the component.

BMW i8 viewed from the rear; the exterior photograph does not show the CFRP passenger cell
BMW i8 exterior. Reinhold Möller / Ermell, CC BY-SA 4.0. Resized; displayed image under the same license.

BMW i8 / Published production route, 2014

Start with the
actual laminate.

BMW identifies the i8 passenger cell as CFRP, made from preformed fiber stacks by high-pressure resin transfer moulding and bonded into the Life module. Its outer skin was largely thermoplastic, with aluminum used for the engine hood and door outer skins. [1]

BMW specifies waterjet contour cutting and opening creation for those CFRP parts, followed by sandblasting of bonding surfaces. The i8 example documents composite finishing; it does not establish rotary-tool use on that line.

Machining considerations

For other structures with permitted CNC features, review the cured geometry, laminate thickness and support close to the cut. Measure holes at the entry and exit, and include the specified laminate-integrity checks.

Include in the brief: Laminate specification, permitted features, datum scheme and exit support.

Review CFRP mounting holes
Porsche 718 Cayman GT4 Clubsport MR on a circuit in the manufacturer’s natural-fiber bodywork report
Porsche 718 Cayman GT4 Clubsport MR. Photograph: Porsche AG.

Porsche / Natural-fiber body kit, 2020

Support the construction
behind the surface.

Porsche’s 2020 GT4 Clubsport MR body kit used flax-based composites for parts including the doors, rear wing, lids, aprons and diffuser. This was a bodywork development, with different constructions across the parts. [2]

The doors used a balsa core and resin transfer moulding. The rear wing used epoxy-impregnated layers cured in an autoclave. Further panels used vacuum infusion and Bcomp powerRibs reinforcement. Those differences change where a fixture can apply load.

Machining considerations

On comparable parts, use trial pieces with the actual core or ribs. Assess fuzzy edges and exposed fibers against the sealing or coating requirement. Record any hand finishing, because it can change panel fit and the intended profile.

Include in the brief: Fiber/resin system, core or ribs, support locations and finished-edge protection.

CFRP battery enclosure prototype from the SGL Carbon and NIO development project
CFRP battery enclosure prototype. Photograph: SGL Carbon.

NIO & HEERO / Two material routes

Protect the mounting
and sealing interfaces.

SGL Carbon’s 2019 NIO project produced CFRP battery enclosure prototypes. The bottom and cover combined sandwich core with carbon-fiber non-crimp fabrics. The release does not establish this construction as standard across NIO vehicles. [3]

A separate 2024 SGL release describes GFRP battery cases supplied to E-Works Mobility for the HEERO electric van after prototype testing, as a small-series application. The glass-fiber material needs its own machining assessment. [4]

Machining considerations

Comparable enclosures may need trimmed perimeters, connector openings and reinforced mounting holes. Identify surfaces that must retain their moulded finish. Keep cutting allowances separate from sealing lands, skins and protective layers.

Include in the brief: Material stack, insert locations, flange requirements, closeouts and final enclosure checks.

Review GFRP edge trimming

Public cases establish material use. The machining notes apply to comparable parts and do not establish CompTex supply or approval by BMW, Porsche, NIO, SGL Carbon or E-Works Mobility.

Match the cutter
to the feature.

Choose a machining task to review the setup, acceptance checks and a relevant CompTex tool. Confirm the exact grade, geometry and coating before a trial.

Cured CFRP / Approved local features

Keep the radius within
the designed allowance.

For a specified contour or pocket, check the floor-to-wall transition and the laminate left below it. A corner-radius tool needs to fit both the feature and the available stock.

Setup
Confirm the cured datum, local thickness, tool reach and fixture contact. Avoid bending a thin shell to make it fit the fixture.
Cut
Match the tool radius to the drawing and review engagement through the transition. Restrict material removal to approved features.
Inspect
Measure the profile and remaining section; assess local fiber damage and the specified laminate integrity.

Cured CFRP / Repeated attachment features

Check the hole
through the laminate.

Diameter and position are part of hole acceptance. The entry, exit and wall also need to meet the drawing’s damage limits as the tool wears.

Setup
Review spindle runout and exit support. Identify any adhesive, insert or metal layer in the feed path.
Cut
Use the actual stack and support condition in the trial. A CFRP-metal stack needs a separate process assessment.
Inspect
Record size, position, exit breakout and wall condition at agreed intervals, with the specified integrity checks.

Glass-fiber composites / Covers and housings

Trial the actual
automotive grade.

Glass fibers are abrasive, while the resin, additives and local construction affect heat response and edge finish. “Fiberglass” alone is not a sufficient material specification.

Material
Record resin, fiber format, thickness and any core, inserts or surface layers in the cut.
Setup
Support the trim line and confirm extraction. Check compatibility of process fluids with later bonding or coating.
Inspect
Examine broken surface fibers, edge damage and the required assembly fit. Track deterioration over cutting length.

Cured CFRP / Slots and cutouts

Plan entry and support
around the opening.

For a permitted internal opening, establish how the cutter enters, how debris leaves and how the remaining material is supported as the cut finishes.

Geometry
Confirm diameter, corner radii, access and tool reach. Identify features already formed by the mould.
Cut
Review the entry path and local engagement. Confirm the CVD diamond variant; the product table also includes DLC options.
Inspect
Check opening size and edge integrity. Complete any specified edge sealing or closeout before assembly.

The products are trial candidates for the stated materials. Natural-fiber parts and mixed-material stacks require their own assessment.

Machine for
the assembly interface.

A finished edge still has to seal, bond or fit the next component. These requirements belong in the process plan before cycle time is compared.

Sealing flanges

Preserve the surface
the seal depends on.

Establish which surfaces may be machined and which must keep their moulded finish. Correcting a flange by cutting deeper can reduce the skin below its permitted thickness or remove a barrier layer. Include the specified geometry, surface condition and assembly checks.

Verify the removal allowance before the trial; complete leak testing where the enclosure specification requires it.

Sandwich & reinforcement

Support the skin
without crushing the core.

Map the facesheets, core, local ribs, potting and inserts. A thin skin can lift at the cutter exit, while clamp pressure can damage the core before cutting starts. Use a representative panel section to establish support and the order of operations.

Check skin-to-core separation and exposed-cell condition. Apply the specified closeout or edge seal after machining.

Datum & assembly fit

Measure with a defined
clamping condition.

A flexible panel may meet the profile in a fixture and move when released. Set the datum scheme, fixture contact and measurement condition. For attachment features, keep hole position tied to the actual assembly interfaces rather than an arbitrary trim edge.

Record whether dimensions are checked clamped, released or in the assembly condition required by the drawing.

Production acceptance

Count parts that
pass inspection.

Record the accepted cutting length or hole count together with the defect that triggers tool replacement. Include inspection, edge sealing and hand finishing when comparing tools. A short trial with a new edge does not establish a production interval.

Check representative parts through tool life and retain the material batch, tool specification, fixture and inspection record.

Use the defect
to guide the review.

Start with where and when the defect appears. These checks help structure a trial; the actual cause still depends on the material, tool and setup.

Include a defect photo
Exit breakout or local delamination

Check exit support, tool wear, runout and the remaining unsupported laminate. Compare the damage location with fiber direction and the material stack. Agree the inspection method before changing the process.

Do not use a diameter-only check to accept a damaged hole.

Fuzzy natural-fiber edges

Review local core or rib support, the cutting edge and the actual flax/resin system. Inspect before and after the specified sealing or coating operation, and record the hand finishing required.

A CFRP-qualified process does not automatically transfer to flax composite.

Flange movement or poor fit

Measure the part in the required condition, then review datum transfer, clamping load and support spacing. Confirm that the cutting allowance permits any proposed correction.

Do not machine away a sealing or barrier layer to compensate for an unexplained fit error.

Edge discoloration or rising rework

Inspect the tool for wear or debris buildup and review local engagement, extraction and workholding. Compare the result over cutting length on the same material grade.

Check the cut and any affected resin against the inspection plan before accepting the part.

Bring the part
and the current issue.

Send the drawing and material stack, with the feature that needs machining. Include a defect photo or inspection result if you are improving an existing process.

xiufeng@hsitool.com

Useful with your enquiry

  • Fiber, resin, thickness, core and inserts
  • Feature, allowance and required finish
  • Machine, holder, support and tool reach
  • Batch size, inspection and rework criteria
All contact options

Your machining brief

For technical review

For CFRP contours: include the corner radius, local thickness, remaining section and permitted allowance.

Sent straight to our engineering team — we reply by email within 24 hours. Drawings and photos can follow in that reply.

Sources & image credits

Published applications

  1. [1] BMW Group: The BMW i8 Production, 2014 (press kit, pp. 3–5)
  2. [2] Porsche: Natural-fiber racing bodywork, 2020
  3. [3] SGL Carbon: NIO battery enclosure prototypes, 2019
  4. [4] SGL Carbon: GFRP battery cases for E-Works Mobility, 2024

Case dates refer to the original publications. Machining guidance describes considerations for comparable components and does not disclose an OEM production process.

Photographs & products

Porsche circuit photograph: Porsche AG, from source [2]. NIO prototype photograph: SGL Carbon, from source [3]. BMW i8 photograph: Reinhold Möller / Ermell, Wikimedia Commons, CC BY-SA 4.0; resized and displayed under the same license. The exterior view does not identify the underlying CFRP structure.

Logo and product visuals: CompTex. Product pages are linked within the corresponding machining tasks. Application images do not imply manufacturer endorsement or a supply relationship.