Leave Your Message
Advanced Aerostructures Tooling Engineering

CFRP Trimming for Carbon/Titanium Stack Drilling & Countersinking

Mastering multi-material aerospace stacks: Eliminating inter-laminar delamination, burr formulation at titanium interfaces, and thermal degradation with sub-micron diamond tooling geometries.

Industrial Status & Engineering Challenges

The Carbon/Titanium Multi-Material Machining Paradigm

In modern commercial aerostructures and defense aviation, hybrid CFRP/Titanium (CFRP/Ti-6Al-4V) stack configurations have become the baseline design for critical load-bearing assemblies.

Conflicting Cutting Physics

CFRP requires high cutting speeds ($V_c > 150\text{ m/min}$) with ultra-sharp shearing edges to fracture brittle carbon fibers without delamination. Conversely, Ti-6Al-4V demands low cutting speeds ($V_c

Interfacial Erosion & Chip Evacuation

During the drilling transition from CFRP to Titanium, continuous, ribbon-like titanium chips are forced upwards through the freshly machined CFRP bore. The highly abrasive titanium chips severely abrade the composite hole wall, causing inner diameter expansion, fiber pull-out, and inter-laminar gap contamination.

Burr Formation & Tight Tolerances

Aerospace assembly tolerances require hole diameter deviations within IT7/IT8 and countersink depth accuracy within $\pm15\ \mu\text{m}$. Exit burrs on the titanium layer cannot exceed $0.05\text{ mm}$ to prevent labor-intensive manual deburring and interfacial gap disassembly in primary structural joints.

< 0.03 mm Titanium Exit Burr Height
± 10 μm Countersinking Depth Accuracy
0% Delam Zero Entry / Exit Delamination
350%+ Tool Life Extension via PCD/CVD
One-Shot Precision

The Mechanics of One-Shot Drilling & Countersinking

The aerospace industry has transitioned decisively away from multi-step drilling (pilot hole followed by reaming and countersinking) to "One-Shot" drilling and countersinking operations. When working with Carbon/Titanium stacks, this process introduces immense thermo-mechanical challenges.

As the drill tip engages the titanium layer, axial thrust force skyrockets by over 300% compared to cutting CFRP. If the tool lacks dedicated differential point geometry, this excessive axial load pushes the titanium ply away from the composite, causing micro-delamination and gap formation at the stack interface.

  • Step Drill Dual Point Geometry: Incorporates a primary $130^\circ-140^\circ$ point angle for balanced titanium penetration and a secondary transitioned flute to sweep carbon fibers cleanly without fraying.
  • Integral Countersink Chamfer: Micro-grain solid carbide or PCD-tipped countersink chamfers designed with variable relief angles to prevent chatter vibrations during combined drilling-countersinking dwell phases.
  • Internal Cryogenic/MQL Channels: Through-tool delivery of Minimum Quantity Lubrication (MQL) directly at the cutting lips to cool the titanium interface without soaking the hygroscopic carbon composite in liquid coolants.
PCD One-Shot Drilling Countersinking Step Drill for CFRP
High-Performance Routing

CFRP Trimming Dynamics: Compression, Shear, and Diamond Coatings

Trimming the peripheral edges of cured composite skins and multi-material wing panels requires strict dimensional conformity and pristine surface finishes. Traditional end mills generate unbalanced axial cutting forces, pulling fibers out of the top surface (up-cut) or causing uncut fiber burs on the bottom surface (down-cut).

Modern CFRP edge trimming relies on multi-flute compression routers and serrated CVD diamond end mills that focus opposite helix vectors toward the centerline of the composite laminate:

  • Neutralizing Shear Forces: Left-hand/right-hand dual helix designs clamp the upper and lower plies inward toward the laminate neutral axis, suppressing delamination even at high feed rates ($f_z > 0.08\text{ mm/tooth}$).
  • Diamond Substrate Supremacy: Chemical Vapor Deposition (CVD) diamond coatings ($10-15\ \mu\text{m}$ thickness) provide a surface hardness approaching $10,000\text{ HV}$, resisting the intense abrasive wearing forces of high-modulus carbon fibers.
  • Ultrasonic-Assisted Trimming: High-frequency axial or tangential vibration (20–40 kHz) converts continuous frictional shear into micro-pulsed fractures, cutting cutting forces by 40% and virtually eliminating resin heat-softening.
Serrated CVD Diamond End Mill for Carbon Composite Trimming
Global Industrial Footprint

Mission-Critical Aerospace & Industrial Applications

Where failure is not an option: Tailored tooling architectures serving the highest tiers of structural aerospace, space exploration, and high-performance mobility.

Commercial Aircraft Wing Boxes

In wide-body passenger jets (e.g., A350, B787), wing spar caps and wing-to-fuselage joints integrate thick CFRP laminates fastened to forged Ti-6Al-4V ribs. CompTex PCD step drills guarantee zero-delamination across more than 50,000 structural fastener holes per airframe.

Defense Aviation & Hypersonic Enclosures

Next-generation combat air systems and missile thermal-protection shrouds combine bismaleimide/carbon composites with titanium substructures. Precision CVD diamond routers execute continuous perimeter contouring with surface roughness ratings of $Ra

Urban Air Mobility & eVTOL

Lightweight carbon-fiber structural chassis in electric vertical takeoff aircraft rely on bonded and bolted titanium joint fittings. Custom ultrasonic profiling blades enable rapid prototyping and trim processing of complex curved composite honeycomb panels with zero crush damage.

Enterprise Capabilities

About HS Industrial

HS Industrial (HSI Group / Xi'an Huishan Industrial Technology Co., Ltd.) is a premier global high-tech enterprise integrating the R&D, manufacture, and technical service of advanced CNC cutting tools. The company boasts a dedicated team of over 200 professionals, including more than 80 R&D experts and engineers (accounting for 40% of the workforce).

Supported by a 4,000-square-meter independent R&D center and a 7,000-square-meter modern production facility, HSI Group is committed to delivering comprehensive, high-precision machining solutions for the global manufacturing industry.

Today, HSI Group's footprint spans across more than 60 countries and regions worldwide. Driven by technological innovation and deep market insights, we have successfully established two flagship brands—CompTex and Huisen—to empower both high-end advanced manufacturing and conventional precision machining.

about us
200+
Professionals
80+
Experts and Engineers
7000m²
Modern Production Facility
60+
Countries and Regions Worldwide
logo11

CompTex Advanced Composites

CompTex is a specialized brand dedicated to high-end composite material machining worldwide. Targeting challenging materials such as Carbon Fiber (CFRP), Glass Fiber (GFRP), Kevlar, and Aramid Honeycomb, we provide comprehensive, end-to-end solutions spanning milling, drilling, grinding, ultrasonic cutting, high-performance tool holders, and specialized hand tools.

CompTex focuses on overcoming industry pain points like delamination, fraying, and rapid tool wear, fully serving top-tier manufacturers in aerospace, new energy, and high-end automotive sectors.

HUISEN PRECISION

Huisen CNC Precision Tooling

Huisen specializes in the R&D and manufacturing of high-quality, standard CNC cutting tools. Our comprehensive product matrix includes CNC inserts, solid carbide end mills, milling chucks/cutters, anti-vibration/damping tools, boring-milling systems, and superhard material (PCD & CBN) inserts.

Huisen delivers high-efficiency, long-life cutting tools optimized for conventional materials like cast iron, stainless steel, and hardened steel, as well as challenging materials like titanium and superalloys. Backed by our powerful R&D capabilities, Huisen also offers custom design and development for tailored, non-standard tooling solutions to meet specific machining challenges.

LOOKING AHEAD

From standard precision tooling to pioneering composite machining solutions, HSI Group always centers on customer needs, defining efficiency through technology and earning trust through quality. We sincerely look forward to forging strong alliances with global partners to shape the future of smart manufacturing. We look forward to collaborating with you!