Compare d1, l2, l1 and d2 in millimeters. Z is a flute count. Confirm the final corner detail and entry capability before selecting a size.
Parts & Applications.
Examples for material and feature review. Each application requires drawing and trial confirmation.
CFRP component detail · CompTex catalog. Selection reference; not a machining case for this model.
CFRP panels
Mounting slots, straight cut-outs and local pockets in carbon-fiber panels and brackets.
Review the layup, panel thickness, slot ends and allowable damage on both faces.
GFRP covers
Access slots and edge features in glass-fiber covers, guards and enclosure panels.
Confirm the resin, backing support, chip removal and surface requirements.
Laminate fixtures
Slots and locating features in composite fixtures, templates and laminate structural parts.
Specify every layer in a hybrid stack; material compatibility requires a separate review.
Catalog material directions include CFRP / GFRP, aramid fiber, hybrid stacks, copper and aluminum with more than 12% silicon. Confirm the exact grade and full stack before selecting a tool.
Before you select.
Review cutting length, corner detail and panel support together.
Composite machining · CompTex catalog reference. The pictured setup is not a trial of this model.
Match the cutting length
The listed l2 is 3–9 mm, even where overall length l1 reaches 105 mm. Check the engaged thickness and toolpath against l2; overall length does not establish cutting depth or neck clearance.
Check the square-end detail
The source describes a protective corner micro-chamfer but gives no chamfer size. Review the finished floor-to-wall detail and slot-end radius. A square end does not make sharp internal corners in plan view.
Support the panel and trial
The source lists 0° straight flutes and Z = 2. Straight geometry does not remove all axial force or replace secure support. Confirm the entry strategy, chip removal and dust control, then inspect both faces after a trial.
Selection questions.
Is CVD diamond the same as solid PCD?
CVD describes chemical vapor deposition; PCD describes polycrystalline diamond. This catalog entry calls the cutting surface a CVD diamond coating, although its category and material tag say PCD. Confirm the construction, substrate and coating specification before ordering.
Can it plunge into a blind slot?
A square profile and two flutes do not establish center-cutting capability. The source supplies no confirmed plunge or ramping limits. Review the final tool drawing and entry route before machining a blind slot.
Does straight flute mean zero pull?
A 0° flute avoids the helix-driven axial component associated with a spiral flute, but cutting forces, tool entry and the setup can still load the panel. Maintain suitable support and verify edge damage on both faces in a representative trial.
Which cutting conditions should I use?
No model-specific speed, feed or depth window is supplied. Share the complete material stack, panel thickness, slot geometry, selected size, machine, holder and quality limits for a tool and process review.
Discuss your part.
Share the material and feature requirements so we can review the tool geometry with you.
This CVD diamond square end mill is listed for slotting carbon- and glass-fiber composite parts. Review slot width, working reach, entry method and panel support together. Confirm the substrate and cutting-surface specification for the selected order number.
Selection considerations
CVD describes chemical vapor deposition; PCD describes polycrystalline diamond. This catalog entry calls the cutting surface a CVD diamond coating, although its category and material tag say PCD. Confirm the construction, substrate and coating specification before ordering.
Application checks
A square profile and two flutes do not establish center-cutting capability. The source supplies no confirmed plunge or ramping limits. Review the final tool drawing and entry route before machining a blind slot.
Discuss your application
For product selection, send CompTex your slot width, cutting depth and workholding. Include the product name, required size or order number, quantity and a drawing so we can review the configuration for your application.
Product Parameters
METRIC
Order Number
d1
l2
l1
d2
Z
5056033001
2
3
50
4
2
5056033002
3
3
75
6
2
5056033003
4
3
75
6
2
5056033004
5
3
75
6
2
5056033005
6
6
100
6
2
5056033006
8
7
100
8
2
5056033007
10
8
100
10
2
5056033008
12
9
105
12
2
Other sizes available upon request. Contact CompTex.