Electroplated diamond grit removes material from composite channels and local planar areas. Match disc thickness to the machining location, then plan contact around the toolpath, workpiece support and dust extraction.
A disc head offers a different contact geometry from a cylindrical burr. Identify the channel boundary or step surface to be refined, then plan tool orientation, access and stock removal.
Disc rim
Channel boundaries and side profiles
Guide the rim along the target profile, using disc thickness and the toolpath to refine the channel boundary. Allow space for the head and shank at the entry, channel ends and adjacent walls.
Selection focusChannel width, entry position, end geometry and sidewall allowance.
Disc face
Open steps and local planar areas
Assess local grinding of accessible step and edge surfaces where face grit coverage and the setup are suitable. Match the contact area to the stock allowance, workpiece support and dust extraction.
Selection focusStep location, approach direction, retained surfaces and contact area.
One 13 mm diameter. Four disc thicknesses.
Match T to the channel profile and machining position.
1mm
Thickness T
2mm
Thickness T
3mm
Thickness T
4mm
Thickness T
T is disc thickness, not channel depth. Finished channel width also depends on the effective abrasive size, runout, wear and toolpath.
Refine channels and steps. Preserve the required profile.
Consider this disc for composite parts with accessible channels, open steps or local edge-finishing needs. A section drawing of the machining area helps selection more than the part name alone.
Locate the step. Identify what must remain.Separate the removal area from the retained profile before selecting thickness and approach direction.
CFRP
Match abrasive configuration to the layup, resin and required channel-edge integrity.
GFRP
Plan trials around cure state, glass-fiber content and the target surface.
Other abrasive materials
Assess sintered carbides and wear-resistant coatings by material and allowance.
Carbon- or glass-fiber panels with open channels
Channel boundaries and local profiles
Refine accessible channels through controlled abrasive contact and adjacent passes. Check disc diameter and access space where the profile includes closed ends or local corners.
Selection focus: width, depth, end geometry and entry/exit clearance.
Composite parts with stepped edges and planar areas
Step surfaces and lap-joint areas
Remove small allowances from open steps, overlap edges or local planes. Identify the permitted removal zone and load-bearing plies, then assess face contact against the target height and finish.
Selection focus: step height, retained plies, surface form and support.
Molded housings, covers and composite flanges
Edge planes and residual material
Dress existing edges or flange areas to blend adjacent profiles to drawing requirements. Plan the approach around fixture positions and control loading and dwell time on thin edges.
Selection focus: edge allowance, flange width, thin-wall support and fit.
Application examples are selection references. The image shows a composite workpiece form, not a result produced by this disc. Confirm channel geometry, edge integrity and surface quality through workpiece trials.
Select thickness. Check the full access envelope.
All four standard sizes have a 13 mm disc diameter, 45 mm overall length and 3 mm shank. Match T to the target profile and check clearance for the head, shank and holder.
Original drawing: DIA (shown as Ø), T, L and Y
DIA
Disc-head diameter
T
Axial disc thickness
L
Overall tool length
Y
Shank diameter
L is not machining depth or permitted overhang. The difference between disc and shank diameter does not establish an allowable channel depth; confirm orientation, clamping and surrounding clearance.
Swipe to view all specifications. Linear dimensions in mm.
Standard diamond grinding discs · Dimensions in mm
Order code
Disc DIA
Thickness T
Overall L
Shank Y
Select size
305900348001
13
1
45
3
305900348002
13
2
45
3
305900348003
13
3
45
3
305900348004
13
4
45
3
Confirm grit, maximum speed and permitted overhang for the material, setup and grinding method. Other sizes are available on request. Include a section drawing of the target channel or step surface when discussing selection.
Remove stock in controlled passes
Plan passes around the allowance and retained channel or step dimensions. Check support and grinding behavior before increasing the contact area.
Clear dust and monitor heat
Use extraction or compatible cooling for the material. Adjust contact and inspect the grit if loading, resin smearing or noticeable heating develops.
Match clamping and speed
Use a holder suitable for the 3 mm shank. Confirm operating conditions against disc diameter, overhang, runout and the tool's permitted limits.
Selection questions
Does thickness T equal the finished channel width?
T is the nominal axial disc thickness. Finished width depends on effective abrasive size, runout, wear and toolpath. Provide the drawing and verify the result by trial where a width tolerance applies; disc thickness alone does not define the finished dimension.
Can it refine the channel wall and floor together?
This depends on actual grit coverage, tool orientation, channel geometry and access. Confirm contact and allowance at both surfaces, and account for the increased load from simultaneous contact. It is not a default method for every channel shape.
How does it differ from a thin diamond slitting wheel?
This range has a 13 mm disc diameter and 1, 2, 3 or 4 mm thickness, focusing on channel and step-surface grinding. Select a dedicated thin wheel for narrower slits. Confirm the permitted speed, clamping and working method separately for each tool type.
What information helps select disc thickness?
Provide the material and cure state, channel or step section, removal allowance, target dimensions and finish. Include the machine, holder and overhang so grit, speed, face contact and cooling can be considered together.
Share the channel or step section. Discuss thickness and toolpath.
Identify the machining location, retained profile and removal allowance so head, shank and holder clearance can be checked.
Electroplated diamond grit removes material from composite channels and local planar areas. Match disc thickness to the machining location, then plan contact around the toolpath, workpiece support and dust extraction.
Selection considerations
T is the nominal axial disc thickness. Finished width depends on effective abrasive size, runout, wear and toolpath. Provide the drawing and verify the result by trial where a width tolerance applies; disc thickness alone does not define the finished dimension.
Application checks
This depends on actual grit coverage, tool orientation, channel geometry and access. Confirm contact and allowance at both surfaces, and account for the increased load from simultaneous contact. It is not a default method for every channel shape.
Discuss your application
For product selection, send CompTex your channel width, disc dimensions and mounting interface. Include the product name, required size or order number, quantity and a drawing so we can review the configuration for your application.