Dimensions match the listing and catalog. The table uses d1; the original drawing uses d for cutting diameter. Confirm the final profile and active cutting length.
Parts & Applications.
Examples for material and feature review. Each application requires drawing and trial confirmation.
AlSiC component references · CompTex catalog. Not a model-specific trial or customer case.
Wafer-tray tooling
Filleted grooves, relief pockets and small contour features in wafer-handling tray components.
Review the substrate, slot width, floor-to-wall radius and neck clearance.
Chucks & fixtures
Shallow pockets and radiused floor-to-wall transitions in semiconductor chuck or fixture components.
Confirm the material grade, working reach, support and allowable edge damage.
Packaging matrices
Corner-radius pockets and contour features in packaging tooling and electronic-module fixtures.
Check the specified fillet, entry strategy, floor tolerance and inspection method.
Catalog-listed material directions: composites, monocrystalline materials, AlSiC, silicon carbide, ceramics, glass and sapphire. Review the exact grade and condition before selection.
Before you select.
Review the corner radius, neck envelope and entry strategy together.
Brand catalog process reference; not a trial of this model.
Match the corner radius
Toric means a corner-radius profile. Compare R and d1 together: the rounded corner changes the floor-to-wall transition. Tool radius alone does not guarantee the finished fillet or an internal corner in plan view.
Check the full neck envelope
Review D1, L1, L2 and shoulder clearance against the pocket. A reduced neck provides relief, but runout, deflection and overhang can still cause contact. L2 is not automatically active cutting depth.
Plan the entry and inspection
Confirm center-cutting capability before any plunge. Use a representative trial to inspect the radius, floor, sidewalls, edge damage and tool wear. Cutting conditions depend on the actual material and setup.
Selection questions.
Is a toric tool the same as a ball nose?
No. A toric tool has a corner radius; a ball nose has a hemispherical end. The listed R values here are smaller than half the listed diameter. Use the final tool drawing to confirm the end-face profile and active cutting geometry.
Will the tool R equal the finished part radius?
R is the listed tool corner radius, not a guaranteed part measurement. Toolpath, orientation, runout, tool condition and the drawing tolerance also matter. Review floor-to-wall fillets separately from internal corners in plan view.
Which materials should I discuss?
The product catalog lists composites, monocrystalline materials, AlSiC, silicon carbide, ceramics, glass and sapphire. Confirm the exact grade and condition; these source-listed directions are not a verified machining window for every substrate.
Which cutting conditions should I use?
No model-specific speed, feed or depth window is supplied. Share the substrate, selected diameter and R, required feature, spindle, holder, support and quality criteria for a geometry review and representative trial.
Discuss your part.
Share the material and feature requirements so we can review the tool geometry with you.
The PCD toric micro end mill is intended for filleted grooves and small die pockets. Match the cutter diameter, corner radius and reduced-neck reach to the drawing. Confirm the actual substrate and permitted edge damage when reviewing semiconductor-tooling applications.
Selection considerations
A toric tool has a corner radius; a ball nose has a hemispherical end. The listed R values here are smaller than half the listed diameter. Use the final tool drawing to confirm the end-face profile and active cutting geometry.
Application checks
R is the listed tool corner radius, not a guaranteed part measurement. Toolpath, orientation, runout, tool condition and the drawing tolerance also matter. Review floor-to-wall fillets separately from internal corners in plan view.
Discuss your application
For product selection, send CompTex your feature size, corner radius and material grade. Include the product name, required size or order number, quantity and a drawing so we can review the configuration for your application.
Product Parameters
METRIC
Order Number
d1
R
D1
L1
L2
L
SD
6056038001
1
0.1
0.95
1.2
6
45
4
6056038002
2
0.1
1.95
1.2
6
45
4
6056038003
3
0.15
2.95
2.5
6
45
4
6056038004
4
0.2
3.95
2.5
6
45
4
6056038005
6
0.5
5.95
2.5
10
50
6
6056038006
8
0.5
7.95
2.5
10
50
8
6056038007
10
1
9.95
2.5
10
50
10
Other sizes available upon request. Contact CompTex.