Leave Your Message

UHD-PA · A Type pneumatic handheld drill

Ultrasonic Handheld Drill for Composite Material Drilling

Small-hole drilling starts
with the right bit and speed.

For composite hole-making requirements up to 6 mm, UHD-PA combines a 350 W pneumatic drive with ultrasonic assistance. Explore configurations for on-site drilling in panels, curved covers and connection flanges, with three models and optional damping or dust collection.

Discuss the A Type drill
CompTex UHD-PA handheld ultrasonic pneumatic drill showing the grip, body and front assembly
Handheld pneumatic configuration. Confirm the drill bit, front attachments and supplied equipment for your setup.
Specified hole diameter
≤6 mm
Pneumatic drill power
350 W
A Type series
3 model options

Smaller holes.
A carefully matched setup.

Handheld operation helps reach on-site hole positions. Hole quality depends on the drill bit, location control, support and feed working together. Ultrasonic assistance can be evaluated to improve cutting contact and reduce drilling thrust; start with the workpiece and the sequence of operations.

  1. 1

    Match the bit and speed version

    Define the material, hole diameter, thickness and layup before choosing the bit and drive configuration. The listed 4,000 / 6,000 / 18,500 rpm values are no-load speeds; loaded operating conditions require separate matching.

  2. 2

    Locate the hole and support the part

    Align the drill axis with the assembly datum and assess jigs, guides and backing. For curved flanges, edge-adjacent holes and hole patterns, establish starting accuracy and support for the final plies.

  3. 3

    Control feed and inspect the first hole

    Maintain feed and chip clearance without prolonged dwelling or chip buildup. Check diameter, bore wall, entry fraying and exit delamination separately, then establish the ongoing process and tool inspection intervals.

This is a manually held drilling tool. Ultrasonic assistance complements secure workholding, guidance and first-part inspection. Verify the result against the actual laminate and drawing requirements.

Three models.
Select for the small-hole task.

UHD-PA40 / UHD-PA60 / UHD-PA185 make up this A Type series. Three no-load speeds are listed separately. Confirm the speed configuration of the selected model; no-load figures are not recommended cutting speeds.

Confirm diameter, bit and speed together.

Select a preferred model and add your material, hole size, quantity and site conditions. If you have not chosen a version, leave the selection at “Please advise”.

Choose a model to add it to your inquiry. Confirm the speed configuration against the bit, diameter, material and thickness.

350 W pneumatic drive / 70 W maximum ultrasonic power
The pneumatic drive rotates the drill bit; the ultrasonic system provides vibration assistance. These are separate specifications for matching the two systems.
6 µm maximum amplitude / 15–30 kHz frequency range
Match the operating point to the generator, handheld unit and bit assembly. Maximum amplitude and the stated frequency range do not define the setting for every job.
A Type does not support amplitude self-adaptation

Confirm the ultrasonic settings and tool assembly separately. Configuration guidance for adaptive-amplitude versions does not apply directly to this model.

≤6 mm is the specified hole range, not chuck capacity or bit shank diameter. Confirm the connection, clamping, air supply and front attachments separately.

UHD-PA A Type technical specifications
Specification Unit Value
Version - A Type
Pneumatic Drill Power W 350
Models - UHD-PA40 / UHD-PA60 / UHD-PA185
No-Load Speed rpm 4,000 / 6,000 / 18,500
Damping Device - Optional
Dust Collection Device - Optional
Amplitude Self-Adaptation - No
Hole Diameter mm ≤ 6 mm
Maximum Ultrasonic Amplitude µm 6
Ultrasonic Frequency kHz 15-30
Maximum Ultrasonic Power W 70

What parts can it drill?
From flanges to panel mounting holes.

These are selection directions within the specified ≤6 mm hole range. Suitability for handheld drilling also depends on access, the drill axis, backing clearance and the required hole quality.

Curved carbon-fiber composite part with a row of holes along its connection flange
Hole positions on a curved composite flangeA workpiece-form reference for tool selection, not a drilling trial result from this handheld unit.

A photo and a local drawing of the hole area help assess grip clearance, jig placement, backing access and the front attachment configuration.

Curved composite components

Small holes in covers, shells and flanges

Assess whether the handheld unit can reach holes on curved surfaces or connection flanges at the required angle. Use a defined datum, guidance and support to control the drill axis on a curved part.

Check: hole-axis direction, edge distance, surface location and front clearance.

Carbon-fiber reinforced polymer · CFRP

Assembly holes in thin panels and covers

Match the bit to mounting holes, locating holes or permitted match-drilling operations. For hole patterns, consider spacing, layup and cutting-edge condition during repeated drilling, with separate entry and exit checks.

Check: layup, backing, hole-position consistency and edge integrity.

Glass-fiber reinforced polymer · GFRP

Insulating panels and composite mounting parts

Select the bit and speed version for the resin system and thickness of glass-fiber plates, connection panels or mounting parts. Include chip clearance, dust collection and bore-wall inspection, and monitor abrasive wear at the cutting edge.

Check: thickness, chip clearance, dust collection and bit wear resistance.

Build the drilling setup
around the handheld unit.

Match the pneumatic drive, ultrasonic equipment, bit and locating aids together. Check the worksite before selecting damping and dust collection, allowing clear sight of the hole and enough operating space.

Digital ultrasonic generator shown as a system configuration reference
Ultrasonic generator matchingConfirm the model, supply voltage, connections and supplied scope with the handheld configuration.
Pneumatic drive
Check air pressure, flow and line preparation at the site. The 350 W rating alone does not establish required pressure, air consumption or drilling torque.
Ultrasonic operating point
Match frequency and amplitude to the generator, handheld unit and bit assembly. A Type has no amplitude self-adaptation; confirm its settings and operating mode during equipment matching.
Location and feed
Confirm the bit connection, projection, drilling jig and backing. Match manual feed to the material and diameter, with position and depth controlled by the actual process.

Optional damping for the handling task

Assess the working posture, number of consecutive holes and locating method. Confirm the device configuration and its effect on front clearance.

Optional dust collection for the hole area

Check the extraction attachment, hose routing and site collection equipment, allowing room for visibility, jig placement and chip clearance.

Selection questions

Does ≤6 mm describe the chuck capacity?

No. It is the specified hole range, not the bit shank diameter or chuck capacity. Confirm the minimum hole size, tool connection, clamping length and front clearance for the selected configuration.

Can 18,500 rpm be used for every material?

No. It is a listed no-load speed. Actual drilling also depends on hole diameter, bit geometry, resin system, thickness, feed and chip clearance. Confirm the model configuration and establish operating conditions through first-part verification.

Does A Type support amplitude self-adaptation?

No. The specification explicitly lists “No”. Confirm the actual ultrasonic settings against the handheld unit, generator and bit assembly rather than assuming the adaptive function of another version.

Are automatic location and feed included?

These functions are not specified. This page describes a manually held tool; arrange location control, guidance, workholding, backing and feed in the drilling process.

How should composite/metal stack drilling be assessed?

Provide the metal type, stack sequence, individual layer thicknesses and acceptance criteria, then match the bit and operating conditions. A single-composite setup should not be transferred directly to aluminum- or titanium-containing stacks.

Share the hole and workpiece.
Match the A Type drill.

Start with product suitability, then confirm the model, bit and site options.

xiufeng@hsitool.com

Creates a local draft without submitting it. Download the text and contact us using the email above.