Leave Your Message

CVD Diamond End Mill for Fiberglass Finishing

CVD Diamond End Mill
for Fiberglass Finishing

Designed for surface quality and high-speed finishing of fiberglass composites.

Solid carbide construction with an 8-flute, flat-end geometry. Finish fiberglass panels, slot walls and stepped faces with a choice of DLC or CVD diamond coating to suit the material and cutting conditions.

Discuss your part
CompTex 8-flute solid carbide flat finishing end mill, original product image
Solid carbide · Flat-end geometry · DLC / CVD diamond options
Cutting diameter d1
4–20 mm
Flute count Z
8 flutes
Coating options
DLC / CVD

Dimensions & sizes

Match diameter, cutting length and coating to the part.
Listed sizes support initial selection; confirm the configuration when ordering.

Original CompTex drawing: cutting diameter d1, cutting length l2, shank diameter d2 and overall length l1
Original CompTex dimension reference.
d1
Cutting diameter
l2
Cutting length
d2
Shank diameter
l1
Overall length
Z
Flute count
DLC / Diamond
Coating codes

9 listed sizes

Swipe the table to compare all dimensions.

Nine listed sizes for the 8-flute flat finishing end mill. Lengths in millimeters; Z is flute count and coating codes have no unit.
Order number d1 l2 d2 l1 Z DLC code CVD code* Select size
3056031001 4 12 4 50 8 4101 6101
3056031002 6 18 6 50 8 4102 6102
3056031003 8 25 8 60 8 4103 6103
3056031004 10 30 10 75 8 4104 6104
3056031005 12 32 12 75 8 4105 6105
3056031006 12 40 12 100 8 4106 6106
3056031007 16 45 16 100 8 4107 6107
3056031008 18 45 18 100 8 4108 6108
3056031009 20 45 20 100 8 4109 6109
Metric · Lengths in mm · Flute count and codes have no unitDiscuss another size

* CVD codes correspond to the catalog's Diamond column. Both coatings are available; source codes are retained as listed. Confirm the complete ordering configuration. Two cutting lengths are listed for the 12 mm diameter.

Part Applications

For fiberglass composite parts,
with a focus on sidewall, slot-wall and stepped-face finishing.

Fiberglass insulation panels

Insulating support plates, isolation panels and mounting plates made from G10 glass-epoxy laminate.

Finish profile sidewalls, mounting-slot walls and local flat surfaces. Check edge fibers, dimensional accuracy and surface quality.

Confirm the laminate grade, resin system, panel thickness and support arrangement.

Composite slot walls & stepped faces

Locating slots, assembly steps and local mounting faces on fiberglass composite structural parts.

Focus on wall and step finishing. Assess the flat-end geometry against the required face and slot-bottom features.

Confirm slot width and depth, internal corners and finishing allowance. Review chip clearance separately for deep slots or full-width cuts.

Illustrative fiberglass insulation mounting plate showing a slot wall, stepped face and profile sidewall; not an actual machining case
Illustrative insulation mounting plate and finishing areas. Original schematic; not a photograph, customer case or dimensioned part drawing.

Selection examples only. Assess the material and cutting conditions through a representative trial; these examples are not verified machining cases for this tool.

Two coating options

Review the coating together with the substrate, edge and process.
Share the material and quality requirements to select a configuration.

DLC

Diamond-like carbon

Available as a coating configuration for this tool. Review the resin system, tendency for material adhesion and required surface quality during selection.

CVD diamond

Crystalline diamond

An option to evaluate where abrasive wear is a concern in composite machining. Review glass-fiber content, edge requirements and the operation to assess suitability.

DLC and CVD diamond are different coating systems. They are not assumed to provide equivalent tool life or surface quality.

Balance finish and cutting efficiency

Match multiple flutes with the high-speed process.
Coordinate feed, cutting load and dust removal.

Put eight flutes to work

With a suitable chip load and stable spindle and workholding, eight flutes can support a higher table feed. Flute count alone does not justify a higher load per tooth or a deeper full-width cut.

Plan a consistent finishing allowance

Leave a consistent allowance on walls, steps and flat faces. Review tool overhang, radial engagement, axial depth and material condition when planning the finishing path.

Match speed with dust control

Set up for high-speed finishing by matching spindle speed and feed to the diameter, coating, resin heat sensitivity and machine capability. Provide effective dust extraction and suitable part support.

Feed relationship

Table feed = spindle speed × flute count × feed per toothA calculation relationship, not a cutting recommendation. Confirm actual settings for the tool, material and machine.

Selection questions

Which machining stage is this tool intended for?

The focus is finishing fiberglass composites, particularly slot walls, profile sidewalls and stepped faces. Review cutting loads and chip clearance separately for heavy roughing, deep slots or full-width cuts.

Are DLC and CVD diamond the same coating?

No. DLC is a diamond-like carbon coating; CVD diamond is a crystalline diamond coating deposited by chemical vapor deposition. Both configurations are available. Select against the material, operation and trial results rather than treating them as interchangeable.

Are eight flutes always faster than fewer flutes?

At the same spindle speed and feed per tooth, more flutes allow a higher theoretical table feed. Actual productivity also depends on cutting load, flute space, dust removal, machine capability and workholding. Confirm the process with a representative trial.

What surface roughness can I expect?

This tool is intended to improve finishing quality. A fixed Ra value or a completely burr-free edge is not specified. Share the required roughness, edge quality, dimensional tolerances and inspection method for evaluation on a representative part.

What should I provide for tool selection?

Material grade and resin system, panel thickness, feature drawings, target surface quality, available spindle speeds, tool overhang, workholding and dust extraction, plus any coating preference.

Discuss your part

Share the material and finishing requirements.
Review the tool size, coating and trial approach with CompTex.

xiufeng@hsitool.com

Choose a listed size above, or describe your machining requirements.

Creates a draft on your device. Your information is not submitted or uploaded.

    product description

    Product overview

    Solid carbide construction with an 8-flute, flat-end geometry. Finish fiberglass panels, slot walls and stepped faces with a choice of DLC or CVD diamond coating to suit the material and cutting conditions.

    Selection considerations

    The focus is finishing fiberglass composites, particularly slot walls, profile sidewalls and stepped faces. Review cutting loads and chip clearance separately for heavy roughing, deep slots or full-width cuts.

    Application checks

    DLC is a diamond-like carbon coating; CVD diamond is a crystalline diamond coating deposited by chemical vapor deposition. Both configurations are available. Select against the material, operation and trial results rather than treating them as interchangeable.

    Discuss your application

    For product selection, send CompTex your glass-fiber grade, flute option and edge requirements. Include the product name, required size or order number, quantity and a drawing so we can review the configuration for your application.

    Product Parameters

    METRIC
    Order Number d1 l2 d2 l1 Z DLC Diamond
    3056031001 4 12 4 50 8 4101 6101
    3056031002 6 18 6 50 8 4102 6102
    3056031003 8 25 8 60 8 4103 6103
    3056031004 10 30 10 75 8 4104 6104
    3056031005 12 32 12 75 8 4105 6105
    3056031006 12 40 12 100 8 4106 6106
    3056031007 16 45 16 100 8 4107 6107
    3056031008 18 45 18 100 8 4108 6108
    3056031009 20 45 20 100 8 4109 6109
    Other sizes available upon request. Contact CompTex.

    Leave Your Message