Leave Your Message

Diamond Coated Carbide Router Burr for CFRP Composite Trimming

Diamond Coated Carbide
Router Burr for CFRP
Composite Trimming

Coarse teeth for efficient cutting. Helical flutes for chip evacuation.

For cutting, profile trimming and stock removal in carbon-fiber and glass-fiber composites. Coarse cutting teeth work with helical chip-clearance flutes. Choose a diamond or DLC coating on a carbide substrate to suit the material and operating conditions.

Discuss your application
CompTex coarse-tooth carbide composite router showing cross-cut teeth and helical flutes
Carbide substrate · Coarse cutting teeth · Helical chip-clearance flutes
Cutting diameter d1
3–12 mm
Cutting length l2
12–50 mm
Listed sizes
13

Coarse-tooth cutting

For sheet separation, contour cutting and stock removal, balancing cutting efficiency with edge requirements.

Helical chip clearance

Flutes provide a path for chips. Match the toolpath and extraction setup to reduce accumulation and recutting.

Two coating options

Diamond or diamond-like carbon (DLC), selected around fiber abrasion, material system and tool-life targets.

Dimensions & specifications

13 listed sizes, with cutting diameters of 3–12 mm.
Diamond or DLC coating selected for your application.

Original dimension drawing: d1 cutting diameter, l2 cutting length, l1 overall length and d2 shank diameter
Original product drawing with the supplied tooth geometry and dimension symbols.
d1
Cutting diameter
l2
Cutting length
l1
Overall length
d2
Shank diameter
Z*
Original flute-count notation

13 sizes

Scroll horizontally to view the complete table.

13 coarse-tooth helical carbide router sizes. Length dimensions in mm; Z has no length unit.
Order number d1 l2 l1 d2 Z* Select size
4056038001 3 12 50 3 8
4056038002 4 12 50 4 8
4056038003 4 20 60 4 8
4056038004 6 12 60 6 8
4056038005 6 18 60 6 8
4056038006 6 25 75 6 8
4056038007 6 32 75 6 8
4056038008 8 18 75 8 10
4056038009 8 25 100 8 10
4056038010 8 32 75 8 10
4056038011 10 25 75 10 12
4056038012 10 38 75 10 12
4056038013 12 50 100 12 12
Metric · Lengths in mm · Z is dimensionlessDiscuss other sizes

* Z retains the original 8 / 10 / 12 notation; confirm the actual tooth configuration when ordering. Cutting length is a geometric dimension. Confirm depth of cut, entry method and feed per tooth for the application.

What can this tool machine?

For sheet cutting, edge trimming and continuous profiles.
Part categories and imagery are selection references.

Carbon-fiber-reinforced polymer (CFRP)

Carbon-fiber panels and profile parts

Equipment panels, connecting plates, flat drone components and other carbon-fiber laminate parts.

Operations: sheet separation, external profile cutting, trimming accessible openings and stock removal before finishing.

Check thickness, layup, support and both edges. Small parts require secure workholding.

Glass-fiber-reinforced polymer (GFRP)

Glass-fiber insulation and structural plates

Insulating mounting plates, composite support plates, equipment panels and flat connecting parts.

Operations: cutting to size, rough profile trimming and accessible opening contours, with a clear chip-exit path.

Check resin, fiber content, heat effects and burr limits. Assess copper-clad boards and composite/metal stacks separately.

Molded CFRP / GFRP components

Molded shell edges and flanges

Accessible molded edges and excess flange material on protective covers and composite housings.

Operations: peripheral trimming, edge stock removal and local contour transitions.

Check support near curved edges, fixture clearance, effective cutting length and actual tool overhang.

Application references are not validated customer cases. Assess thin walls, copper-clad boards, honeycomb, sandwich structures and composite/metal stacks separately.

Coatings for your material

Diamond and DLC are both available options.
Evaluate cutting behavior and replacement criteria.

Diamond coating

For abrasive fiber composites

A wear-resistant option for abrasive cutting in CFRP and GFRP, helping extend usable tool life.

Evaluate the fiber/resin system, tooth wear, edge-quality changes and replacement criteria. Confirm the coating process and specification when ordering.

DLC coating

Diamond-like carbon option

An alternative coating configuration to assess against the material system, friction and adhesion behavior, with cutting performance and operating cost in mind.

Evaluate material compatibility, chip buildup, tooth wear and part quality. DLC and diamond are distinct coatings; compare service life under the same conditions.

Confirm the coating process, thickness and applicable parameters with the supplied configuration. Compare durability under equivalent cutting conditions.

Efficient cutting needs a clear chip-exit path

Match tooth geometry, toolpath, support and extraction.
Verify the setup against edge quality and dimensions.

Pair flute clearance with extraction

Helical flutes help chips leave the cutting zone. Results depend on cutting load, available clearance and extraction position. Watch for buildup in enclosed slots or deeper areas; adjust the path and cutting stages as needed.

Inspect both edges

Support the workpiece close to the cut to limit vibration and loss of support near the exit. Inspect entry and exit edges as well as the sidewall, then adjust the toolpath to the layup and acceptance criteria.

Compare life on a consistent basis

Keep material, tool size, path, parameters and workholding consistent when comparing coatings. Record cutting length or part count alongside wear, burrs and dimensional change, using part-quality limits to set the replacement point.

Include in your application review

Fiber/resin system, thickness, cutting location, stock allowance, workholding, extraction and edge acceptance criteria.Confirm spindle speed, feed, cutting depth and entry method for the tool size and setup.

Selection questions

Which operations suit the coarse-tooth design?

This tool focuses on efficient CFRP and GFRP cutting, peripheral trimming and stock removal. Confirm the final surface result against the material and layup in a representative trial. Add a separate finishing operation where finer tool marks or tighter surface requirements call for it.

Do helical flutes replace dust extraction?

Use effective extraction suited to the material and machine. Helical flutes provide a chip-clearance path; they do not replace external extraction or guarantee a clear slot at every depth. Include the cutting location, stock allowance and extraction arrangement in the application review.

How should I choose diamond or DLC?

Start with the fiber/resin system, cutting load, adhesion and wear behavior. Compare coatings against part quality and replacement criteria. Both are available options; no same-condition comparative life data has been supplied for this product.

Does Z count every individual tooth tip?

The source table lists Z as 8, 10 or 12. The coarse cross-cut geometry also has individual tooth features, so this column alone does not establish the total number of tooth tips or a feed-per-tooth value. Confirm the supplied geometry and cutting parameters together.

Can I cut full-width slots or plunge vertically?

Sheet separation can be considered, but full-width engagement, cutting stages and entry method depend on diameter, cutting length, material and workholding. Center-cutting capability is not established in the current data. Confirm the entry strategy before vertical plunging or blind-pocket roughing.

Discuss your application

Tell us the material, thickness and cutting location.
Review the size, coating and trial-cut requirements.

xiufeng@hsitool.com

Select a size above or describe your application below.

Creates a draft on this device. No information is submitted or uploaded.

    product description

    Product overview

    For cutting, profile trimming and stock removal in carbon-fiber and glass-fiber composites. Coarse cutting teeth work with helical chip-clearance flutes. Choose a diamond or DLC coating on a carbide substrate to suit the material and operating conditions.

    Selection considerations

    This tool focuses on efficient CFRP and GFRP cutting, peripheral trimming and stock removal. Confirm the final surface result against the material and layup in a representative trial. Add a separate finishing operation where finer tool marks or tighter surface requirements call for it.

    Application checks

    Use effective extraction suited to the material and machine. Helical flutes provide a chip-clearance path; they do not replace external extraction or guarantee a clear slot at every depth. Include the cutting location, stock allowance and extraction arrangement in the application review.

    Discuss your application

    For product selection, send CompTex your material, removal allowance and coating choice. Include the product name, required size or order number, quantity and a drawing so we can review the configuration for your application.

    Product Parameters

    Order Number d1 l2 l1 d2 Z Diamond DLC
    4056038001 3 12 50 3 8 7936 2031
    4056038002 4 12 50 4 8 7937 2232
    4056038003 4 20 60 4 8 7938 2433
    4056038004 6 12 60 6 8 7939 2634
    4056038005 6 18 60 6 8 7940 2835
    4056038006 6 25 75 6 8 7941 3036
    4056038007 6 32 75 6 8 7942 3237
    4056038008 8 18 75 8 10 7943 3438
    4056038009 8 25 100 8 10 7944 3639
    4056038010 8 32 75 8 10 7945 3840
    4056038011 10 25 75 10 12 7946 4041
    4056038012 10 38 75 10 12 7947 4242
    4056038013 12 50 100 12 12 7948 4443

    Leave Your Message